[Product Introduction] Milk-V Duo is an MPU developed based on CVITEK CV1800B chip that can run LINUX and RTOS.. Milk-V Duo provides professionals,IoT enthusiasts, hobbyists, DIYers a reliable, low-cost and extremely capable platform for building and tinkering with their ideas, helping them become Reality.    

[Product parameters] Processor: CVITEK CV1800B (906@1GHz; 906@700MHz). Memory: DDR2 64MB. Storage: 1 Mirco-SD slot, 1 SD NAND pad. USB: 1 Type-C for data and power, 1 USB2 pad. Camera: 1 16P FPC socket (MIPI CSI 2 channels). GPIO : 26 pins available for general purpose I/O (GPIO). Size: 21mm X 51mm    

processor:. 1GHz and 70OMHZ RISC-V C906 processor.Integrate CVITEK TPU to realize intelligent detection. Support H.264/H.265 video encoding, up to 2880x1620@20fps. Compatible with HD CMOS sensors. Programmable frequency output for sensor clock. Comprehensive ISP features for image optimization. Some OpenCV libraries support CV hardware acceleration. 16-bit audio codec with built-in microphone input and output. Flexible network configuration with 1 Ethernet PHY    

CSI-2 (MIPI Serial Camera):With 16-pin FPC interface for 2-wire MIPI camera input. Operate l2C, CLK and RST signals at 1.8V voltage level    

Ethernet:Milk-V Duo includes CV1800B chip and 100Mbps physical layer. PHY connected to 5-pin pad. Ethernet use requires external transformer and RJ45 socket.    

GPIOs:    

[Up to 26 GPIO pins on the MilkV Duo 40-pin header to access internal peripherals such as SDIO, I2C, PWM, SPI, J-TAG, and UART.    

Up to 3xI2C    

up to 5xUART    

Up to 1xSDIO1    

Up to 1xSPI    

Up to 2xADC    

Up to 7xPWM    

Up to 1xRUN    

Up to 1xJTAG    

USB interface:    

Compatible with USB 2.0, backward compatible with USB 1.1    

Support for various speed modes, host/device capabilities and transports    

protocol:    

Scalable interface via USB hub (up to 127 devices)    

Power saving mode, support HID devices    

USB with configurable software    

USB Type-C for accessing storage media    

Micro-SD:    

SDIO 0 is compatible with the Secure Digital Storage (SD3.0) protocol    

Board Specifications:    

Single-sided PCB    

Thickness: 1mm    

Type-C port located on the top edge    

Dual Slotted/Through Hole Headers Around Remaining Edge    

Available as surface mount modules or in dual in-line package (DIP) format    

40 primary user pins on 2.54mm (0.1inch) pitch grid with 1mm holes    

Compatible with veroboard and breadboard    

Please note that due to different batches, there may be differences in the appearance, color, and printing of the product, which will not affect its use    

Colour: random color , don't accept the specified color    

Material:PCB    

Package Contents:    

1 x Development Board    

Only the above package content, other products are not included.    

Note: Light reflection and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1-3cm.   

         1 PCS RISC-V Milk-V Duo Development Board Dual Core CV1800B PCB Development Board Support Linux For Iot Enthusiasts DIY Gamers     

       [Product Introduction] Milk-V Duo is an MPU developed based on CVITEK CV1800B chip that can run LINUX and RTOS.. Milk-V Duo provides professionals,IoT enthusiasts, hobbyists, DIYers a reliable, low-cost and extremely capable platform for building and tinkering with their ideas, helping them become Reality.    

[Product parameters] Processor: CVITEK CV1800B (906@1GHz; 906@700MHz). Memory: DDR2 64MB. Storage: 1 Mirco-SD slot, 1 SD NAND pad. USB: 1 Type-C for data and power, 1 USB2 pad. Camera: 1 16P FPC socket (MIPI CSI 2 channels). GPIO : 26 pins available for general purpose I/O (GPIO). Size: 21mm X 51mm    

processor:. 1GHz and 70OMHZ RISC-V C906 processor.Integrate CVITEK TPU to realize intelligent detection. Support H.264/H.265 video encoding, up to 2880x1620@20fps. Compatible with HD CMOS sensors. Programmable frequency output for sensor clock. Comprehensive ISP features for image optimization. Some OpenCV libraries support CV hardware acceleration. 16-bit audio codec with built-in microphone input and output. Flexible network configuration with 1 Ethernet PHY    

CSI-2 (MIPI Serial Camera):With 16-pin FPC interface for 2-wire MIPI camera input. Operate l2C, CLK and RST signals at 1.8V voltage level    

Ethernet:Milk-V Duo includes CV1800B chip and 100Mbps physical layer. PHY connected to 5-pin pad. Ethernet use requires external transformer and RJ45 socket.    

GPIOs:    

[Up to 26 GPIO pins on the MilkV Duo 40-pin header to access internal peripherals such as SDIO, I2C, PWM, SPI, J-TAG, and UART.    

Up to 3xI2C    

up to 5xUART    

Up to 1xSDIO1    

Up to 1xSPI    

Up to 2xADC    

Up to 7xPWM    

Up to 1xRUN    

Up to 1xJTAG    

USB interface:    

Compatible with USB 2.0, backward compatible with USB 1.1    

Support for various speed modes, host/device capabilities and transports    

protocol:    

Scalable interface via USB hub (up to 127 devices)    

Power saving mode, support HID devices    

USB with configurable software    

USB Type-C for accessing storage media    

Micro-SD:    

SDIO 0 is compatible with the Secure Digital Storage (SD3.0) protocol    

Board Specifications:    

Single-sided PCB    

Thickness: 1mm    

Type-C port located on the top edge    

Dual Slotted/Through Hole Headers Around Remaining Edge    

Available as surface mount modules or in dual in-line package (DIP) format    

40 primary user pins on 2.54mm (0.1inch) pitch grid with 1mm holes    

Compatible with veroboard and breadboard    

Please note that due to different batches, there may be differences in the appearance, color, and printing of the product, which will not affect its use    

Colour: random color , don't accept the specified color    

Material:PCB    

Package Contents:    

1 x Development Board    

Only the above package content, other products are not included.    

Note: Light reflection and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1-3cm.