Features
High performance: This AIO uses high thermal conductivity silicone inside and aluminum alloy housing outside for better heat dissipation; Because of this, it has excellent water and dust resistance up to IP67. It can be used even after 30 minutes of immersion in fresh water. Suitable for various climates and harsh environments.
High reliability and durability: Built-in F411 FC, 6S-45A ESC, ELRS 2.4GHz receiver, each interface on the AIO has short circuit protection, even if one interface is protected due to some factors, the other interfaces can be used normally.
Rich interface: This AIO is reserved for Analog CAM, Analog VTX, CADDX VISTA KIT null terminal, SBUS Port, UART1 plug-and-play interface to meet the needs of different users.
Parameter configuration.
FC: MCU STM32F411CEU6 (100MHz)
IMU: MPU6500
OSD: Betaflight OSD AT7456E
RF Chip:SX1281 (2.4GHz)
Firmware target: Betaflight__DARWINF4SX1280
BEC output: 5V/0.5A x 3 & BAT/0.75A x 2
Port resources:2x Uarts (1,2)
1x Softuart (Apply for VTX)
1x SBUS (RX1 inverter)
ESC: MCU EFM8BB21F16G
Input Voltage: 3-6S LiPo
Continuous current: 45A
MAX current:(5 seconds): 55A
ESC Traget:J_H_40
Size: L46.2mm x W39.5mm x H10mm
Installing Hole: 25.5x25.5mm (M2)
Weight:41.5g
Caution.
①Seawater is very corrosive, this AIO is not recommended for seawater environment, once it falls into seawater, please use fresh water to clean it immediately.
②The AIO supports 3-6S battery, remember not to reverse the battery connection, otherwise it will burn the AIO.
③After receiving the product, first enter Betaflight to check whether the gyroscope and accelerometer are detected and whether the gyroscope attitude is normal.
④Pull the throttle in Betaflight to make sure the four motors rotate normally including the correct motor steering, and then install the paddle for test flight; make sure to unload the paddle when pulling the throttle to avoid major accidents.
Confirm the above notes without any product problems can be installed paddles and start to fly cool!
Packing list.
1 x AIO
5 x spare cable
7 x screws
3 x TYPE-C rubber plugs
7 x SH1.0 socket plugs
1 x sticker
1 x instruction manual
Logistics information
Our products are located in Hong Kong, China, and the logistics speed depends on your specific location. According to our experience, it usually takes about 15-20 days of transportation time
CONTACT US
RETURNS POLICY
Lorem ipsum dolor sit amet, consectetur adipiscing elit. Morbi ut blandit risus. Donec mollis nec tellus et rutrum. Orci varius natoque penatibus et magnis dis parturient montes, nascetur ridiculus mus. Ut consequat quam a purus faucibus scelerisque. Mauris ac dui ante. Pellentesque congue porttitor tempus. Donec sodales dapibus urna sed dictum. Duis congue posuere libero, a aliquam est porta quis.
Donec ullamcorper magna enim, vitae fermentum turpis elementum quis. Interdum et malesuada fames ac ante ipsum primis in faucibus.
Curabitur vel sem mi. Proin in lobortis ipsum. Aliquam rutrum tempor ex ac rutrum. Maecenas nunc nulla, placerat at eleifend in, viverra etos sem. Nam sagittis lacus metus, dignissim blandit magna euismod eget. Suspendisse a nisl lacus. Phasellus eget augue tincidunt, sollicitudin lectus sed, convallis desto. Pellentesque vitae dui lacinia, venenatis erat sit amet, fringilla felis. Nullam maximus nisi nec mi facilisis.
SHIPPING
Lorem ipsum dolor sit amet, consectetur adipiscing elit. Morbi ut blandit risus. Donec mollis nec tellus et rutrum. Orci varius natoque penatibus et magnis dis parturient montes, nascetur ridiculus mus. Ut consequat quam a purus faucibus scelerisque. Mauris ac dui ante. Pellentesque congue porttitor tempus. Donec sodales dapibus urna sed dictum. Duis congue posuere libero, a aliquam est porta quis.
Donec ullamcorper magna enim, vitae fermentum turpis elementum quis. Interdum et malesuada fames ac ante ipsum primis in faucibus.
Curabitur vel sem mi. Proin in lobortis ipsum. Aliquam rutrum tempor ex ac rutrum. Maecenas nunc nulla, placerat at eleifend in, viverra etos sem. Nam sagittis lacus metus, dignissim blandit magna euismod eget. Suspendisse a nisl lacus. Phasellus eget augue tincidunt, sollicitudin lectus sed, convallis desto. Pellentesque vitae dui lacinia, venenatis erat sit amet, fringilla felis. Nullam maximus nisi nec mi facilisis.

How to choose the correct size:
Step 1 Please measure your foot length carefully.

Step 2 Please choose the correct size according to your foot length and chinese size.
For example, If your foot length is 255 mm , you should choose the size 8.
