jumbospot SHARI SA818 Ham Allstar Radio Interface Compatible Raspberry Pi 2/3/4 hosted Allstar node UHF 1W hotspot

2 sold in last 8 hours
mickcara
cwad0000145
In stock
$186.88
Size Guide
$186.88
customers are viewing this product
Tags:
SHARI (SA818 Ham Allstar Radio Interface) is a ham construction project designed by N8AR that implements a Raspberry Pi hosted Allstar node using a NiceRF SA818 embedded UHF (420 -450 MHz) radio module. SHARI is designed for construction and use in the amateur radio service by licensed amateur radio operators who can assure that their assembled SHARI kit meets FCC mandated operating requirements including RF frequency, deviation and required power levels at the fundamental and harmonic frequencies.


In order to create an Allstar node, SHARI plugs into two USB jacks on a Raspberry Pi2/Pi3 or Pi4 for power, the Allstar interface and radio programming (a short M/F USB extender cable can be used if desired).

Front panel LEDs indicate the status of SHARI – [POWER (green), USB Audio CONNECTION STATUS (blinking green), COS (green) and PTT (red)] . SHARI RF output power is 500 to 1000(default) milliwatts.

Features:


Works with a Pi2/Pi3 or Pi4 (USB connector positions swapped)
Uses the Cmedia CM119B or CM108B USB audio IC
Uses a NiceRF SA818 UHF or VHF embedded radio module
500 to 1000(default) milliwatts RF output power
Small, portable with self contained radio and antenna
Radio settings changed using a program running on the Raspberry Pi

Required Hardware:

1.A fully assembled SHARI Pi3U, Pi3V, Pi4U or Pi4V.
2.A Raspberry Pi 2, Pi 3 or Pi4 . The Pi2 or Pi3 is normally used with the SHARI Pi3(U) ,while the Pi4 is normally used with the SHARI Pi4(U)
3.A case for the Raspberry Pi. A metal case is preferred but if you want to use a WiFi connection instead of a wired network connection then a plastic case may be required to obtain adequate range.
4.A micro SD card – 16GB or larger, Class 10 or better is recommended.
5.A power supply for the Pi-This should be a power supply intended for the version of the Raspberry Pi. These supplies typically provide 5.1 to 5.2 VDC to the Pi. Current requirements vary with version. Numerous problems with Allstar Nodes have been traced to inadequate power supplies.

SHARI Allstar Node Setup and Configuration Guide (In short version)

1.Create an Account with Allstar
2.Create a Server and Request a Node number
3.Software
4.Configuring Allstar
5.Configuring SimpleUSB-Tune-Menu for SHARI

RETURNS POLICY

Lorem ipsum dolor sit amet, consectetur adipiscing elit. Morbi ut blandit risus. Donec mollis nec tellus et rutrum. Orci varius natoque penatibus et magnis dis parturient montes, nascetur ridiculus mus. Ut consequat quam a purus faucibus scelerisque. Mauris ac dui ante. Pellentesque congue porttitor tempus. Donec sodales dapibus urna sed dictum. Duis congue posuere libero, a aliquam est porta quis.

Donec ullamcorper magna enim, vitae fermentum turpis elementum quis. Interdum et malesuada fames ac ante ipsum primis in faucibus.

Curabitur vel sem mi. Proin in lobortis ipsum. Aliquam rutrum tempor ex ac rutrum. Maecenas nunc nulla, placerat at eleifend in, viverra etos sem. Nam sagittis lacus metus, dignissim blandit magna euismod eget. Suspendisse a nisl lacus. Phasellus eget augue tincidunt, sollicitudin lectus sed, convallis desto. Pellentesque vitae dui lacinia, venenatis erat sit amet, fringilla felis. Nullam maximus nisi nec mi facilisis.

SHIPPING

Lorem ipsum dolor sit amet, consectetur adipiscing elit. Morbi ut blandit risus. Donec mollis nec tellus et rutrum. Orci varius natoque penatibus et magnis dis parturient montes, nascetur ridiculus mus. Ut consequat quam a purus faucibus scelerisque. Mauris ac dui ante. Pellentesque congue porttitor tempus. Donec sodales dapibus urna sed dictum. Duis congue posuere libero, a aliquam est porta quis.

Donec ullamcorper magna enim, vitae fermentum turpis elementum quis. Interdum et malesuada fames ac ante ipsum primis in faucibus.

Curabitur vel sem mi. Proin in lobortis ipsum. Aliquam rutrum tempor ex ac rutrum. Maecenas nunc nulla, placerat at eleifend in, viverra etos sem. Nam sagittis lacus metus, dignissim blandit magna euismod eget. Suspendisse a nisl lacus. Phasellus eget augue tincidunt, sollicitudin lectus sed, convallis desto. Pellentesque vitae dui lacinia, venenatis erat sit amet, fringilla felis. Nullam maximus nisi nec mi facilisis.

How to choose the correct size:

Step 1 Please measure your foot length carefully.

Step 2 Please choose the correct size according to your foot length and chinese size.

For example, If your foot length is 255 mm , you should choose the size 8.

Step 3 If you\'re not sure of the correct size, you can click chat with us!

WHATSAPP:+8613625959351

Avoir des questions? Demandez à un expert
jumbospot SHARI SA818 Ham Allstar Radio Interface Compatible Raspberry Pi 2/3/4 hosted Allstar node UHF 1W hotspot
You have successfully subscribed!