{"product_id":"puhui-t862-infrared-rework-bga-station-irda-welder-t862-bga-machin","title":"PuHui T862++ INFRARED REWORK BGA STATION IRDA WELDER T862++ BGA MACHIN","description":"\u003cdiv\u003e\u003cspan\u003e\u003cp\u003e\u003cspan\u003e\u003cbr\u003e\u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003e Operation method\u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003e   1. Locate, choose and attach the appropriate lens: \u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003e \u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003e   The usable of the lenses diameter are 28mm, 38mm, 48mm. \u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003e \u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003e   (1)When the area of the chips is below 15mm*15mm, please choose the IR-lamp temperature about 160-240C, and choose the lens which D=28mm to avoid destroying other places, usually it will take you about 20-40seconds. \u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003e \u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003e   (2)When the area of the chips is between 15mm*15mm and 30mm*30mm, please choose the IR-lamp temperature about 240-320C, and choose the lens which D=38mm to avoid destroying other places, usually it will take you about 30-60seconds. \u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003e \u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003e   (3)When the area of the chips is above 30mm*30mm, please choose the IR-lamp temperature 350C(Attention: you should turn on the pre-heat dish first, and set-up the temperature about 150-200C,wait 3-5minutes to allow the temperature steady on the set-up temperature),and choose the lens which D=48mmto avoid destroying other places, and keep the lamp body direct light. You should control the time carefully to avoid burning the chips \u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003e \u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003e   Warning: \u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003e \u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003e   The light system will shoot straightly. Please pay more attention to yourself control time to avoid burning out. \u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003e \u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003e   2. Open the machine \u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003e \u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003e   (1) Check if the connection wire of the lamp body and the 936-Iron is ok. \u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003e   (2) Locate and attach the power cable to the rear of the re-work station \u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003e   (3) Confirm all front panel rocker switches are off. \u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003e   (4) Place the rear AC Power Switch in the ON Position. \u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003e   (5) Allow the T-862++ Power-On-Self-Test (POST) to complete. \u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003e   (6) Temperature set-points will display last value used. \u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003e   (7) Place the target PC Board on the slip-rack and orient to close proximity of estimated position of focused Infrared light, \u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003e   (8) Adjust the T-862++ Infrared light system height, allow 20-30mm from lens end to PC board target component. (9) Turn on the two switches. They control warm-up plate and light system. \u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003e \u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003e   3. PC Board Component Removal and Replacement. \u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003e \u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003e   (1)Put the PCB board onto the holder \u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003e   (2)Turn on the switch of the pre-heat dish, and set-up the temperature \u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003e   (3)Turn on the switch of the IR-Lamp, Regulate the temperature (the temperature must be warm enough to allow the solder to be liquefied), focus the Infrared light on the chip to be removed. \u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003e   (4)Once the solder liquefied and melted, use tweezers to remove the chip. \u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003e \u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003e   4. Soldering a chip. \u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003e \u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003e   (1) Clean the target pad with the brush \u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003e   (2) Then put the solder ball and a flat of solder flux on the target pad \u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003e   (3) Turn on the switch of the pre-heat dish, and set-up the temperature \u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003e   (4)Turn on the switch of the IR-Lamp, Regulate the temperature (the temperature must be warm enough to allow the solder to be liquefied), focus the Infrared light on the chip to be soldered. \u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003e   (5) Wait to allow the Infrared lamp to heat the solder flux to work as the solder balls on the target chip pad reaches liquid temperature. Use tweezers or a vacuum device to place the chip target position. Once the solder liquefies, the chip will be sold automatically. \u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003e   After cooling the chip, pick up the PCB board, check if it is ok. If not, re-operate. \u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003e \u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003e   5. The use of the 936 searing-iron \u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003e \u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003e   It can be used separately, But be sure it must be connect with the chassis. \u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003e   If the component is too small, you needn’t use the IR-lamp, the 936 searing-iron is enough. \u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003e   Open the switch of the 936 searing-iron, set-up the temperature, then use it as you want.\u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003eMaintenance: \u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003e   ü At all times – Insure the light body cooling fan is unobstructed and clean. \u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003e \u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003e   ü Use a little machine oil. Lubricate the focus holder and cell guide to inhibit rusting, keep them ease to operate. \u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003e \u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003e \u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003e   Warning ! \u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003e \u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003e   The T-862++ System creates temperatures in excess of high degrees via Infrared Light. Wear appropriate eye protection or any device within the T-862++when using it. After use, Do not cut the power immediately, confirm the light body is cool-to-touch, Turn off the power switch, then place the system in airiness \u0026amp;amp;amp; safety storage. \u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003e \u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003e   Do NOT use this system or any associated device in an environment conducive to fire or electrical overload. \u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003e \u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003e   Disconnect the AC Power Plug when not in use. \u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003e \u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003e   When using, it is of high temperature, Do NOT allow children or the un-trained to touch the T-862++\u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cbr\u003e\u003c\/p\u003e\u003c\/span\u003e\u003c\/div\u003e","brand":"mickcara","offers":[{"title":"220V","offer_id":41383212744841,"sku":"03189-1","price":666.0,"currency_code":"USD","in_stock":true},{"title":"110V","offer_id":41383212777609,"sku":"03189-2","price":666.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0365\/2131\/2393\/files\/528555e305a8e836312f6df0f5ada975.jpg?v=1694934202","url":"https:\/\/mickcara.com\/products\/puhui-t862-infrared-rework-bga-station-irda-welder-t862-bga-machin","provider":"mickcara","version":"1.0","type":"link"}